An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D (22)

Number of Channels

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.

Total RMS Power Output

Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

Up to 250 watts (2)

250–500 watts (10)

500–1,000 watts (10)

Total Peak Power Output

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

Up to 500 watts (9)

500–1,000 watts (5)

1,000–2,000 watts (8)

Minimum Impedance Unbridged

The lowest impedance the amplifier will handle when it is not bridged.

2 (21)

Minimum Impedance Bridged

The lowest impedance the amplifier will handle when it is bridged.

Not Bridgeable (11)

4 ohms (7)

Remote bass/level controller

If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.

No (7)

Yes (7)

Optional (5)

Preamp Outputs

Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

1 pair (6)

No (5)

2 pairs (1)

Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker Level Inputs

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.

Yes (7)

No (6)

Optional (6)

Yes - with included adapter (1)

Maximum Input Gauge Size

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.

Deals

Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

FREE Amp Kit (1)

Memorial Day Sale (1)

On Sale (1)

Availability

In Stock (16)

Out of stock (6)

Shop the Category

Filters & Sort

Sort

Best Match

Best Rated
Biggest $ savings off list price
Biggest % savings off list price
Price: Lowest First
Price: Highest First
Product Name: A-Z
Product Name: Z-A
Newest First

Kenwood eXcelon XR901-5 + NVX XKIT46

1800W Max (900W RMS) XR Series 2-ohm Stable Class-D 5-Channel Amplifier w/ Bass Knob Included + NVX Premium 4 Gauge 6-Channel Amp Wiring Kit

Compare

Go to item page

Kenwood eXcelon XR901-5 + NVX XKIT46

1800W Max (900W RMS) XR Series 2-ohm Stable Class-D 5-Channel Amplifier w/ Bass Knob Included + NVX Premium 4 Gauge 6-Channel Amp Wiring Kit

• 60 Watts x 4, 400W x Sub Channel RMS @ 4 ohm
• 75 Watts RMS x 4, 600W x Sub Channel @ 2 ohm
• Total Peak Power: 1800 Watts
• CEA-2006 Compliant
• Remote Bass Knob Included
• Heavy Duty Aluminum Heatsink
• Dimensions:10-1/4" W x 6-5/8" L x 1" H

Free shipping in USA. Provide zip for delivery date.

empty

Was $879.99 Details

$804.98

In stock

Only 1 Left!

Add to Cart

Kenwood KAC-D3104 + NVX XFLOC4 Line-Output-Converter + Amp Kit

Class D 4-Channel Amplifier (600 Watts Peak Power) + NVX 4-Channel L.O.C. + 8 Gauge Amp Kit

Compare

Go to item page

Kenwood KAC-D3104 + NVX XFLOC4 Line-Output-Converter + Amp Kit

Class D 4-Channel Amplifier (600 Watts Peak Power) + NVX 4-Channel L.O.C. + 8 Gauge Amp Kit

• 4 ohm: 50 watts x 4 chan.
• 2 ohm: 75 watts x 4 chan.
• Total Peak Power: 600 Watts
• Speaker Level Input
• Signal Sensing Turn-On
• Variable Low Pass/High Pass Filter
• Variable Bass Boost: 0 to +18 dB bass boost at 40 Hz

Free shipping in USA. Provide zip for delivery date.

empty

Was $433.72 Details

$296.87

In stock

Add to Cart

Kenwood KAC-D3104 with Amplifier Wiring Kit

Class D 4-Channel Amplifier (600 Watts Peak Power)

Compare

Go to item page

Kenwood KAC-D3104 with Amplifier Wiring Kit

Class D 4-Channel Amplifier (600 Watts Peak Power)

• 4 ohm: 50 watts x 4 chan.
• 2 ohm: 75 watts x 4 chan.
• Total Peak Power: 600 Watts
• Speaker Level Input
• Signal Sensing Turn-On
• Variable Low Pass/High Pass Filter
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $409.98 Details

$281.48

In stock

Add to Cart

Kenwood eXcelon XM802-5 with Amplifier Wiring Kit

1600W Peak (800W RMS) Class D 5-Channel Car Audio Amplifier

Compare

Go to item page

Kenwood eXcelon XM802-5 with Amplifier Wiring Kit

1600W Peak (800W RMS) Class D 5-Channel Car Audio Amplifier

• 75 watts x 4 channel + 300 watts x 1 channel @ 4 ohm
• 75 watts x 4 channel + 500 watts x 1 channel @ 2 ohm
• Bridged: 150 watts x 2 channel @ 4 ohm + 500 watts x 1 channel @ 2 ohm
• Total RMS Power: 800 watts
• CEA-2006 Compliant
• Class D 2 ohm Stable 5-Channel Amplifier
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $739.99 Details

$498.98

In stock

Add to Cart

Kenwood KAC-9106D w/Belva 1.0 Farad Capacitor + Belva 2000 Watt Handling Amp Kit

1000W RMS Class D Monoblock Car Amplifier w/ 1.0 Farad Capacitor & 4 AWG Amp Kit

Compare

Go to item page

Kenwood KAC-9106D w/Belva 1.0 Farad Capacitor + Belva 2000 Watt Handling Amp Kit

1000W RMS Class D Monoblock Car Amplifier w/ 1.0 Farad Capacitor & 4 AWG Amp Kit

• Kenwood KAC-9106D Performance Series 1000W Class-D Monoblock Amplifier
• Belva BAK42 Complete 4 Gauge 2-Channel Amplifier Installation Kit
• Belva BB1D 1.0 Farad Capacitor
• RMS: 500W x 1 @ 4 ohm
• Premium Power and Ground Wire Provides Optimal Power Transfer

Free shipping in USA. Provide zip for delivery date.

empty

168

Was $539.98 Details

$419.97

In stock

Add to Cart

Kenwood KAC-9106D with NVX 4 Gauge Amp Kit

2000W RMS Performance Series Class-D Monoblock Amplifier

Compare

Go to item page

Kenwood KAC-9106D with NVX 4 Gauge Amp Kit

2000W RMS Performance Series Class-D Monoblock Amplifier

• 500 watts x 1 channel @ 4 ohm
• 1000 watts x 1 channel @ 2 ohm
• Total RMS Power: 1000 watts
• Class D 2 ohm Stable Monoblock Amplifier
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

149

Was $543.99 Details

$433.98

In stock

Add to Cart

• 500 watts x 1 channel @ 4 ohm
• 1000 watts x 1 channel @ 2 ohm
• Total RMS Power: 1000 watts
• Class D 2 ohm Stable Monoblock Amplifier
• Includes Amplifier Wiring Kit

Kenwood KAC-M8005 + NVX XKIT46 4 Gauge Amp Wiring Kit

5-Channel Marine Class-D Amplifier (800W RMS)

Compare

Go to item page

Kenwood KAC-M8005 + NVX XKIT46 4 Gauge Amp Wiring Kit

5-Channel Marine Class-D Amplifier (800W RMS)

• 50 Watts RMS x 4 @ 4 ohm + 300 watts x 1 chan.
• 75 Watts RMS x 4 @ 2 ohm + 500 watts x 1 chan.
• Bridged: 150 Watts RMS x 2 @ 4 ohm
• Total Peak Power: 1600 Watts
• CEA-2006 Compliant
• Variable high-pass filter: 50 - 200 Hz, 12dB/octave
• Variable low-pass filter: 50 - 200 Hz, 24 dB/octave (sub)
• Extruded Aluminum Heat Sink Design
• Dimensions: 9"W x 7 3/8"L x 2 3/16"H
• Includes NVX XKIT46 4 Gauge Amp Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $699.99 Details

$604.98

In stock

Only 2 Left!

Add to Cart

Kenwood eXcelon XR1001-1 + High Quality NVX Amp Kit

2000W Max (1000W RMS) XR Series 2-ohm Stable Class-D Monoblock Amplifier w/ Bass Knob Included

Compare

Go to item page

Kenwood eXcelon XR1001-1 + High Quality NVX Amp Kit

2000W Max (1000W RMS) XR Series 2-ohm Stable Class-D Monoblock Amplifier w/ Bass Knob Included

• 500 Watts RMS x 1 @ 4 ohm
• 1000 Watts RMS x 1 @ 2 ohm
• Total Peak Power: 2000 Watts
• CEA-2006 Compliant
• Bass Knob Included
• Aluminum Heatsink
• Dimensions: 12-5/8" W x 6-5/8" L x 2" H

Free shipping in USA. Provide zip for delivery date.

empty

117

Was $843.99 Details

$783.98

In stock

Only 2 Left!

Add to Cart

Kenwood eXcelon XR601-1 + NVX Premium XKIT42

600W RMS XR Series 2-ohm Stable Class-D Monoblock Amplifier w/ Bass Knob Included + NVX 4 Gauge Amp Wiring Kit

Compare

Go to item page

Kenwood eXcelon XR601-1 + NVX Premium XKIT42

600W RMS XR Series 2-ohm Stable Class-D Monoblock Amplifier w/ Bass Knob Included + NVX 4 Gauge Amp Wiring Kit

• 400 Watts RMS x 1 @ 4 ohm
• 600 Watts RMS x 1 @ 2 ohm
• Total Peak Power: 1200 Watts
• CEA-2006 Compliant
• Bass Knob Included
• Aluminum Heatsink
• Dimensions: 8-11/16" W x 6-5/8" L x 1-3/8" H

Free shipping in USA. Provide zip for delivery date.

empty

116

Was $593.99 Details

$533.98

In stock

Only 1 Left!

Add to Cart

Kenwood eXcelon XR401-4 with NVX 4 Gauge Amp Kit

400W RMS Excelon Series Class-D 4-Channel Amplifier w/ Bass Knob

Compare

Go to item page

Kenwood eXcelon XR401-4 with NVX 4 Gauge Amp Kit

400W RMS Excelon Series Class-D 4-Channel Amplifier w/ Bass Knob

• 75 watts x 4 channel @ 4 ohm
• 100 watts x 4 channel @ 2 ohm
• Bridged: 200 watts x 2 channel @ 4 ohm
• Total RMS Power: 400 watts
• Class D 2 ohm Stable 4-Channel Amplifier
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $605.99 Details

$540.98

In stock

Only 3 Left!

Add to Cart

Kenwood eXcelon XM160-2 with NVX 8 Gauge Amp Kit

160W RMS eXcelon Series Class D 2-Channel Compact Amplifier for select 2014-up Harley-Davidson® motorcycles

Compare

Go to item page

Kenwood eXcelon XM160-2 with NVX 8 Gauge Amp Kit

160W RMS eXcelon Series Class D 2-Channel Compact Amplifier for select 2014-up Harley-Davidson® motorcycles

• 80 watts x 2 channel @ 2 ohm
• Total RMS Power: 160 watts
• Class D 2 ohm Stable 2-Channel Amplifier
• Plug & Play Power, Speaker, & Input Wiring
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $665.99 Details

$525.98

In stock

Only 1 Left!

Add to Cart

• 80 watts x 2 channel @ 2 ohm
• Total RMS Power: 160 watts
• Class D 2 ohm Stable 2-Channel Amplifier
• Plug & Play Power, Speaker, & Input Wiring
• Includes Amplifier Wiring Kit

Kenwood eXcelon XR901-5 with NVX XDSP66BT

900W RMS 5-Channel Amplifier with 15 Band Parametric EQ Digital Signal Processor

Compare

Go to item page

Kenwood eXcelon XR901-5 with NVX XDSP66BT

900W RMS 5-Channel Amplifier with 15 Band Parametric EQ Digital Signal Processor

FREE Amp Kit at Checkout! Shop deal

Free shipping in USA. Provide zip for delivery date.

empty

Was $1049.99 Details

$834.98

In stock

Only 1 Left!

Add to Cart

Top special offer for this item

Save 25% on a Compatible Belva Amplifier Wiring Kit

Kenwood eXcelon XM160-2-98 with NVX 8 Gauge Amp Kit

160W RMS eXcelon Series Class D 2-Channel Amplifier for Select 98-13 Harley Davidson Motorcycles

Compare

Go to item page

Kenwood eXcelon XM160-2-98 with NVX 8 Gauge Amp Kit

160W RMS eXcelon Series Class D 2-Channel Amplifier for Select 98-13 Harley Davidson Motorcycles

• 80 watts x 2 channel @ 2 ohm
• Total RMS Power: 160 watts
• Class D 2 ohm Stable 2-Channel-Channel Amplifier
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $635.99 Details

$495.98

In stock

Only 1 Left!

Add to Cart

• 80 watts x 2 channel @ 2 ohm
• Total RMS Power: 160 watts
• Class D 2 ohm Stable 2-Channel-Channel Amplifier
• Includes Amplifier Wiring Kit

Kenwood KAC-D8105 with NVX 4 Gauge Amp Kit

1600 Watts Max Power 5-Channel Class D Amplifier

Compare

Go to item page

Kenwood KAC-D8105 with NVX 4 Gauge Amp Kit

1600 Watts Max Power 5-Channel Class D Amplifier

• Kenwood KAC-D8105 5 Channel Amplifier
• Peak Power: 1600 watts
• 50 watts RMS x 4 + 300 watts at 4 Ohm
• 75 watts x4 + 500 watts at 2 Ohm
• Dimensions: 9"W x 2-3/16"H x 7-3/8"D

• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $699.99 Details

$524.98

In stock

Add to Cart

Kenwood eXcelon XM302-4 with NVX 4 Gauge Amp Kit

300W RMS XR Series Class-D 4-Channel Marine Amplifier

Compare

Go to item page

Kenwood eXcelon XM302-4 with NVX 4 Gauge Amp Kit

300W RMS XR Series Class-D 4-Channel Marine Amplifier

• 50 watts x 4 channel @ 4 ohm
• 75 watts x 4 channel @ 2 ohm
• Bridged: 150 watts x 2 channel @ 4 ohm
• Total RMS Power: 300 watts
• Class D 2 ohm Stable 4-Channel Amplifier
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $605.99 Details

$390.98

In stock

Only 1 Left!

Add to Cart

Lowest price in 30 days

Kenwood eXcelon XM802-5 with NVX 4 Gauge Amp Kit

800W RMS XR Series Class-D 5-Channel Marine Amplifier

Compare

Go to item page

Kenwood eXcelon XM802-5 with NVX 4 Gauge Amp Kit

800W RMS XR Series Class-D 5-Channel Marine Amplifier

• 50 watts x 4 channel + 300 watts x 1 channel @ 4 ohm
• 75 watts x 4 channel + 500 watts x 1 channel @ 2 ohm
• Bridged: 150 watts x 2 channel @ 4 ohm + 500 watts x 1 channel @ 2 ohm
• Total RMS Power: 800 watts
• Class D 2 ohm Stable 5-Channel Amplifier
• Includes Amplifier Wiring Kit

Free shipping in USA. Provide zip for delivery date.

empty

Was $829.99 Details

$554.98

In stock

Add to Cart

Kenwood eXcelon XM502-1 with Amplifier Wiring Kit

1000W Peak (500W RMS) Class D Monoblock Car Audio Amplifier

Out of stock

Compare

Go to item page

Kenwood eXcelon XM502-1 with Amplifier Wiring Kit

1000W Peak (500W RMS) Class D Monoblock Car Audio Amplifier

• 300 watts x 1 channel @ 4 ohm
• 500 watts x 1 channel @ 2 ohm
• Total RMS Power: 500 watts
• Class D 2 ohm Stable Monoblock Amplifier

empty

Was $499.99 Details

$327.98

Add to Cart

• 300 watts x 1 channel @ 4 ohm
• 500 watts x 1 channel @ 2 ohm
• Total RMS Power: 500 watts
• Class D 2 ohm Stable Monoblock Amplifier

Kenwood KAC-M5024BT with NVX 8 Gauge Amp Kit

300W RMS KAC Series Class-D 4-Channel Marine Amplifier With Bluetooth® Connectivity

Out of stock

Compare

Go to item page

Kenwood KAC-M5024BT with NVX 8 Gauge Amp Kit

300W RMS KAC Series Class-D 4-Channel Marine Amplifier With Bluetooth® Connectivity

empty

Was $547.99 Details

$482.98

Add to Cart

Kenwood KAC-M3001 with Belva 8 Gauge Amp Kit

300W RMS KAC Series Class-D Monoblock Marine Amplifier

Out of stock

Compare

Go to item page

Kenwood KAC-M3001 with Belva 8 Gauge Amp Kit

300W RMS KAC Series Class-D Monoblock Marine Amplifier

• 200 watts x 1 channel @ 4 ohm
• 300 watts x 1 channel @ 2 ohm
• 300 watts x 1 channel @ 1 ohm
• Total RMS Power: 300 watts
• Class D 2 ohm Stable Monoblock Amplifier
• Includes Amplifier Wiring Kit

empty

Was $299.99 Details

$246.98

Notify Me

Kenwood eXcelon XM502-1 with NVX 8 Gauge Amp Kit

500W RMS XR Series Class-D Monoblock Marine Amplifier

Out of stock

Compare

Go to item page

Kenwood eXcelon XM502-1 with NVX 8 Gauge Amp Kit

500W RMS XR Series Class-D Monoblock Marine Amplifier

• 300 watts x 1 channel @ 4 ohm
• 500 watts x 1 channel @ 2 ohm
• Total RMS Power: 500 watts
• Class D 2 ohm Stable Monoblock Amplifier
• Includes Amplifier Wiring Kit

empty

Was $545.99 Details

$355.98

Add to Cart

• 300 watts x 1 channel @ 4 ohm
• 500 watts x 1 channel @ 2 ohm
• Total RMS Power: 500 watts
• Class D 2 ohm Stable Monoblock Amplifier
• Includes Amplifier Wiring Kit

1 2 Next

Items per page: 20 40 60

Clear all

We love people and we're ready to help you! See what separates us from our competition.

Free perks, no Prime^TM fees

Take advantage of our VIP rewards like 10% back on your purchases, free 2-day shipping, extended warranties, and free returns! Gain access to all of these rewards without any membership fees.

Free install gear for stereos

Get great discounted (and possibly FREE) installation accessories with most car stereo purchases. This includes dash kits, wiring harnesses and antenna adapters that you will need to properly install your new car stereo.

Authentic & Authorized

We are an Authorized Dealer for all the brands we sell, including the most premium brands in car and marine audio such as Hertz, JL Audio, NVX, Rockford Fosgate, Kicker, Alpine, Kenwood and many more.

View best sellers, deals, and more

Shop Deals and get up to 30% off premium brands! Shop Now! We are always looking out for the best products and deals to offer our customers. Don’t pay too much by shopping elsewhere!

Learn about All Car Audio

We have information on brands, gear, and more for you to explore! Check out our YouTube Channel for helpful how-to videos, product reviews, and Q&As. For a more detailed look, also visit our Learning Center!

Call or email our experts

Our trained experts are here to assist you! They are just a phone call or click away to help you get the right gear for you and your vehicle!

Why Shop With Us?

Subscribe

Welcome to the Team!

Kenwood Car Amplifier Packages & Bundles

Shop the Category

Kenwood eXcelon XR901-5 + NVX XKIT46

Kenwood eXcelon XR901-5 + NVX XKIT46

Kenwood KAC-D3104 + NVX XFLOC4 Line-Output-Converter + Amp Kit

Kenwood KAC-D3104 + NVX XFLOC4 Line-Output-Converter + Amp Kit

Kenwood KAC-D3104 with Amplifier Wiring Kit

Kenwood KAC-D3104 with Amplifier Wiring Kit

Kenwood eXcelon XM802-5 with Amplifier Wiring Kit

Kenwood eXcelon XM802-5 with Amplifier Wiring Kit

Kenwood KAC-9106D w/Belva 1.0 Farad Capacitor + Belva 2000 Watt Handling Amp Kit

Kenwood KAC-9106D w/Belva 1.0 Farad Capacitor + Belva 2000 Watt Handling Amp Kit

Kenwood KAC-9106D with NVX 4 Gauge Amp Kit

Kenwood KAC-9106D with NVX 4 Gauge Amp Kit

Kenwood KAC-M8005 + NVX XKIT46 4 Gauge Amp Wiring Kit

Kenwood KAC-M8005 + NVX XKIT46 4 Gauge Amp Wiring Kit

Kenwood eXcelon XR1001-1 + High Quality NVX Amp Kit

Kenwood eXcelon XR1001-1 + High Quality NVX Amp Kit

Kenwood eXcelon XR601-1 + NVX Premium XKIT42

Kenwood eXcelon XR601-1 + NVX Premium XKIT42

Kenwood eXcelon XR401-4 with NVX 4 Gauge Amp Kit

Kenwood eXcelon XR401-4 with NVX 4 Gauge Amp Kit

Kenwood eXcelon XM160-2 with NVX 8 Gauge Amp Kit

Kenwood eXcelon XM160-2 with NVX 8 Gauge Amp Kit

Kenwood eXcelon XR901-5 with NVX XDSP66BT

Kenwood eXcelon XR901-5 with NVX XDSP66BT

Kenwood eXcelon XM160-2-98 with NVX 8 Gauge Amp Kit

Kenwood eXcelon XM160-2-98 with NVX 8 Gauge Amp Kit

Kenwood KAC-D8105 with NVX 4 Gauge Amp Kit

Kenwood KAC-D8105 with NVX 4 Gauge Amp Kit

Kenwood eXcelon XM302-4 with NVX 4 Gauge Amp Kit

Kenwood eXcelon XM302-4 with NVX 4 Gauge Amp Kit

Kenwood eXcelon XM802-5 with NVX 4 Gauge Amp Kit

Kenwood eXcelon XM802-5 with NVX 4 Gauge Amp Kit

Kenwood eXcelon XM502-1 with Amplifier Wiring Kit

Kenwood eXcelon XM502-1 with Amplifier Wiring Kit

Kenwood KAC-M5024BT with NVX 8 Gauge Amp Kit

Kenwood KAC-M5024BT with NVX 8 Gauge Amp Kit

Kenwood KAC-M3001 with Belva 8 Gauge Amp Kit

Kenwood KAC-M3001 with Belva 8 Gauge Amp Kit

Kenwood eXcelon XM502-1 with NVX 8 Gauge Amp Kit

Kenwood eXcelon XM502-1 with NVX 8 Gauge Amp Kit

Didn't find your car?

Account

Shopping help

Company

Everyday heroes

Brand stores

Useful links