JVC Monoblock Amplifiers at Sonic Electronix

JVC Monoblock Amplifiers

JVC has decades of car audio and monoblock amplifier experience.
Filters
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

This designates the series of the amplifier. Many amps are available in a litany of different wattage and channel configurations, but maintain consistent features throughout the product line.
The lowest impedance the amplifier will handle when it is not bridged.
The lowest impedance the amplifier will handle when it is bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
listview icon
gridview icon
JVC KS-AX201

500W Max AX2 Series Class AB Monoblock Amplifier

KS-AX201 main
Go to item page

500W Max AX2 Series Class AB Monoblock Amplifier

• RMS Power: 150W x 1 @ 4 ohms, 250W x 1 @ 2 ohms
• Total Peak Power: 500W
• Variable low-pass filter: 50 - 200 Hz
• Speaker-level (high-level) inputs

9
JVC KS-AX201

500W Max AX2 Series Class AB Monoblock Amplifier

OUT OF STOCK

$199.95 (57.99% off)
$83.99

Item Added to Cart

KS-AX201 small

500W Max AX2 Series Class AB Monoblock Amplifier

$83.99

Keep Shopping

Belva BAK82

Complete 8 Gauge Amplifier Wiring Kit with 2-Channel RCA Interconnects

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the JVC KS-AX201.
JVC KS-DR3001D

800W Peak (400W RMS) DRVN Series Class-D 2-Ohm Stable Monoblock Power Amplifier

KS-DR3001D main
Go to item page

800W Peak (400W RMS) DRVN Series Class-D 2-Ohm Stable Monoblock Power Amplifier

• RMS: 4 ohm: 250 Watts x 1 chan.
• RMS: 2 ohm: 400 Watts x 1 chan.
• Total Peak Power: 800 Watts
• Speaker-level (high-level) inputs
• Variable low-pass filter: 50 - 200 Hz
• Variable Bass Boost: 0 to +18 dB bass boost

2
JVC KS-DR3001D

800W Peak (400W RMS) DRVN Series Class-D 2-Ohm Stable Monoblock Power Amplifier

OUT OF STOCK

$209.95 (33.34% off)
$139.95

Item Added to Cart

KS-DR3001D small

800W Peak (400W RMS) DRVN Series Class-D 2-Ohm Stable Monoblock Power Amplifier

$139.95

Keep Shopping

Belva 1.0 Farad Capacitor + Amp Kit

BB1D 1.0 Farad Capacitor + BAK42BK Complete 4 Gauge Amplifier Wiring Kit

$54.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the JVC KS-DR3001D.
JVC KS-AX201 + Free 8 Gauge Belva Amplifier Kit

500W Max AX2 Series Class AB Monoblock Amplifier + BAK82

KS-AX201, BAK82 main
Go to item page

500W Max AX2 Series Class AB Monoblock Amplifier + BAK82

• RMS Power: 150W x 1 @ 4 ohms, 250W x 1 @ 2 ohms
• Total Peak Power: 500W
• Variable low-pass filter: 50 - 200 Hz
• Speaker-level (high-level) inputs

68
JVC KS-AX201 + Free 8 Gauge Belva Amplifier Kit

500W Max AX2 Series Class AB Monoblock Amplifier + BAK82

OUT OF STOCK

$239.94 (49.70% off)
$120.69

Related Categories


JVC Marine Amplifiers JVC Marine Amplifiers

Enhance the sound on your boat by adding an amplifier to your marine audio system. These marine amps are the perfect way to get louder, bigger, and clearer sound quality on your boat. These marine amplifiers can be great for standard boat speakers, tower speakers, and even some marine PA systems. Each amp is specially treated and engineered to function in the same wet, salty environment that boats are in.

JVC Motorcycle Amplifiers JVC Motorcycle Amplifiers

Your motorcycle will sound better than ever with the proper amplifier. Most of these amps are specially designed with special materials that can withstand the vibrations and elemental exposure, while others are designed with an extremely small footprint to fit conveniently in a saddlebag or other tight installations. Many of the products in this category are specifically designed for certain motorcycles, making installation a breeze.

JVC Monoblock Amplifiers Information

The JVC monoblock amplifiers are designed for efficient power output. These amps take up little space and feature high quality platinum finished connections, and solid power ratings. You won't be disappointed with your JVC monoblock amplifier for your vehicle's needs.
    clear all items