Power Acoustik 2-Channel Amplifiers

filter-icon Filters & Sort
Loading...
Filters
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

Many brands group their products into series or lines of products to help customers know the level of quality (good, better, best for example). You can filter by series and the brand using our guided browsing.
The lowest impedance the amplifier will handle when it is not bridged.
The lowest impedance the amplifier will handle when it is bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
Power Acoustik MOFO2-2KD

2000W Peak (600W RMS) MOFO Series Class D 2-Channel Car Amplifier

MOFO2-2KD main
Go to item page

2000W Peak (600W RMS) MOFO Series Class D 2-Channel Car Amplifier

• 200 watts x 2 channel @ 4 ohms
• 300 watts x 2 channel @ 2 ohms
• Bridged: 600 watts x 1 channel @ 4 ohms
• Total RMS Power: 600 watts
• Class D 2 ohms Stable 2-Channel Amplifier

shipping truck icon
FREE shipping to VA. Get it Fri, June 9

empty

$109.99

Available

Ships in 10-14 days

• 200 watts x 2 channel @ 4 ohms
• 300 watts x 2 channel @ 2 ohms
• Bridged: 600 watts x 1 channel @ 4 ohms
• Total RMS Power: 600 watts
• Class D 2 ohms Stable 2-Channel Amplifier

MOFO2-2KD small

Item added to your cart.

Price: $109.99

Allstate logo

Keep your product protected longer! Extend the warranty after the manufacturer warranty expires. 

  • Mechanical, electrical and product failure covered! 100% parts and labor covered. (Coverage starts after Mfr. warranty)
  • Easy online management! Zero hassle claim service, Available 24/7
Essential add-ons
Belva BAK82

Complete 8 Gauge Amplifier Wiring Kit with 2-Channel RCA Interconnects

$49.99

$29.99

Add to cart
NVX Remote Level Bass Control

Controls bass level and frequency

$29.99

$19.99

Add to cart
NVX XMICROLOC2

Add a 2-Channel amp without replacing your factory radio

$19.99

$14.99

Add to cart
NVX XBBR2

Looking to fine tune the bass in your vehicle? Look no further

$149.99

$89.99

Add to cart
NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft 2-Channel RCA Audio Interconnect Cable with Twisted Pair Construction

$18.99

$18.99

Add to cart
80 Amp Smart Relay Isolator (XSBI80)

Smart isolator - Monitors and auto-charging feature!

$49.99

$29.99

Add to cart
NVX XCAP1F

True 1.0 Farad 20V Capacitor with Digital Read-out, Built-in Distribution Block

$124.99

$79.99

Add to cart
Belva Nine Function Digital Multimeter

Perfect for any installation and troubleshooting

$29.99

$9.99

Add to cart
Pair of 8 Gauge Spade Terminals, #8 Opening

Spade Terminals • 8 Gauge • 1 Red & 1 Black • Nickel Plated

$9.99

$9.99

Add to cart
NVX XUBT3

Universal Bluetooth Audio Receiver & Volume/Playback Controller Knob

$99.99

$59.99

Add to cart
    clear all
    why-shoping-with-sonic

    We love people and we're ready to help you! See what separates us from our competition.

    Take advantage of our VIP rewards like 10% back on your purchases, free 2-day shipping, extended warranties, and free returns! Gain access to all of these rewards without any membership fees.
    Get great discounted (and possibly FREE) installation accessories with most car stereo purchases. This includes dash kits, wiring harnesses and antenna adapters that you will need to properly install your new car stereo.
    We are an Authorized Dealer for all the brands we sell, including the most premium brands in car and marine audio such as Hertz, JL Audio, NVX, Rockford Fosgate, Kicker, Alpine, Kenwood and many more.
    Shop Deals and get up to 30% off premium brands! Shop Now! We are always looking out for the best products and deals to offer our customers. Don’t pay too much by shopping elsewhere!
    We have information on brands, gear, and more for you to explore! Check out our YouTube Channel for helpful how-to videos, product reviews, and Q&As. For a more detailed look, also visit our Learning Center!
    Our trained experts are here to assist you! They are just a phone call or click away to help you get the right gear for you and your vehicle!
    Why Shop With Us?

    Add vehicle

    Save up to 10 different vehicles in your garage

    Loading...
    < Back