NVX XSP65KIT w/ NVX XSP692

Have these installed on the front doors of my f150 with the tweeters installed in the factory locations, the tweeters require a 1-3/4 inch hole saw bit if you are modifying a location this will give you a very snug friction fit. I used liquid nails LN-2000 in a thin layer to make sure they didn’t slowly push out due to temperature changes.

I have them paired to a set of the NVX XSP652 in the rear, and am pushing them with an NVX XAD41 amp getting signal from my Sony XAV-AX6000 head unit off the 5v RCA pre amp outputs.

These match perfectly to the XSP652 in the rear for volume clarity,etc, and get very loud and play very clear provided you are doing what you can to keep noise down(low gain settings, aftermarket radio with high voltage preamps, keeping head unit volume below 80% and amp gain lowish).

The crossovers are fairly large and have a lot of empty space, and we’re a problem for my installation requiring a different install placement than planned. I wish they made them smaller and there really is no reason why the couldn’t have.

The tweeters were pretty well balanced, but I turned down the top frequencies in my head unit eq two clicks to be less harsh at higher volumes(personal taste). These have excellent bass for 6.5 inch speakers but are still 6.5 inch speakers. I wish they made the 6x9 version of these in a component set. They are adequate for most music by themselves but I still recommend getting a subwoofer to fill in that lower range.

I have my HPF on my head unit set to 50hz with a -36db slope and that seems like a good place to start tuning with these.

Be aware that these do not include any mounting screws and will not fit any standard 5x7/6x8 to 6.5 inch adapter bracket, they have an over sized basket and the mounting holes for the speakers will not line up with those adapter plates and the speaker stops 2 inches shy of flush because the center hole is not big enough, these baskets too large to alter the brackets. I had to fab my own with some cheap plastic cutting boards, drill bits, and a oscillating multi tool.

By Frank R on July 7, 2023 Verified purchase

Great sound for a banging price

I wanted some Focal speakers but they were super expensive. I found these nvx carbon fiber ones and decided to give them a go. I was impressed by the packaging but more impressed by the sound. I will for sure be trying out some other nvx stuff in the future

Nice speakers, but lacks basic features

Sound decent. Tweeters have zero hardware for installation. You have to press fit them into a perfectly sized hole, then glue or tape them in place. Far from ideal.

By Zeke on September 14, 2023 Verified purchase

Sounds amazing

2013 tahoe ltz. I've installed several different name brand components over the years dating back to 1997.

I will say these are freaking loud and clear. Impressive for the price. Currently running off factory bose amp. Will run new speaker wire and install crossovers when I have time to install the nvx vad11005 amp. I'm hoping that adding the crossover will tone down the highs. Currently have my eq set at -8 to -12 for the higher frequencies.

I ended up gluing the tweeters on the back side of the a-pillar to keep the bose factory cover.
I had speaker adapters already for the doors from some pioneer coaxials that were already installed in my truck.

Easy install.

By RICKY on February 18, 2023 Verified purchase

Not bad

People have been putting these on motorcycles and they are fair for bass in a saddle bag and the price isn't bad either. Definitely recommend these.

Great upgrade for the price

I bought two pairs of these for my 2022 Ram 2500 with the base audio system. The site shows that they don't fit in the front doors, but they did. I put a layer of foam between the speaker and the plastic door mount and with a little coaxing of the factory screws they fit just fine. I have not installed my amplifiers yet, but on factory radio power the clarity of these speakers still comes through! They are very well built, and if the rated power handling is correct they should sound terrific once they get ~125 watts to them through my Fosgate T400-4. The low end on factory power is lacking, but with the LC7i we are installing that should be resolved. I will update my review once we get some real power to them in a couple of weeks!

By Eric on April 5, 2022 Verified purchase

So far, so good

Better than what I had before, Sound is very clean, worth the upgrade fooorsure????

By K on August 27, 2023 Verified purchase

Good 6.5 component

For the price they sound pretty good. Had to do alot of tweaking to get them though but for the price it's a bargain. rReally light and fast cones.

By jeremy on February 28, 2023 Verified purchase

Awesome service!

I ordered the product on Friday (NZ time) and it was delivered on Tuesday morning!!! Super fast!
Installed and working perfectly as expected!
Awesome speakers!

By David on August 5, 2022 Verified purchase