All AudioControl Car Amplifiers at Sonic Electronix

All AudioControl Car Amplifiers

Filters
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

The lowest impedance the amplifier will handle when it is not bridged.
The lowest impedance the amplifier will handle when it is bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
listview icon
gridview icon
AudioControl LC-6.1200

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

LC-6.1200 main
Go to item page

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

• 750 Watts RMS x @ 4 ohms
•1,200 Watts RMS x 1 @ 2 ohms
• 400 Watts RMS Bridged, 4 ohm
• 6 Preamp Outputs
• AccuBASS bass control
• Aluminum Alloy Chassis
• 12" W x 7.95" L x 2.10" H

2
AudioControl LC-6.1200

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

In stock

$869.99 (11.49% off)
$769.99
Hide info
More info Item page
2 Special offers
  • Get A Free $50 Gift Card With Purchase!
  • Get a Free Audio Control Remote With Purchase!

Item Added to Cart

LC-6.1200 small

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

$769.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$49.99

Add
Stinger SI4612 4000 Series Interconnect Cable

12 ft. 6-Channel 4000 Series Audio Interconnect Cable

$19.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl LC-6.1200.
AudioControl LC-1.800

800W RMS Series 2-ohm Stable Monoblock Amplifier

LC-1.800 main
Go to item page

800W RMS Series 2-ohm Stable Monoblock Amplifier

• 500 Watts RMS x 1 @ 4 ohms
• 800 Watts RMS x 1 @ 2 ohms
• AccuBASS Processing Built In
• GTO Signal Sense
• MILC Level Matching
• Linkwitz-Riley Crossovers

5
AudioControl LC-1.800

800W RMS Series 2-ohm Stable Monoblock Amplifier

In stock

Only 1 Left!

$499.99 (10.01% off)
$449.95
Hide info
More info Item page
1 Special offer
  • Save 50% off True 4 Gauge Wiring Kit with Select Amps

Item Added to Cart

LC-1.800 small

800W RMS Series 2-ohm Stable Monoblock Amplifier

$449.95

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$49.99

Add
NVX XLCA2

2 Channel Line Out Converter with xBOOST & 3-year warranty*!

$89.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl LC-1.800.
AudioControl D-4.800

800W RMS D-Series 4-Channel Amplifier with Digital Signal Processor

D-4.800 main
Go to item page

800W RMS D-Series 4-Channel Amplifier with Digital Signal Processor

• D-Series 4-Channel Amplifier with Digital Signal Processor
• 4 ohms: 125 watts x 4 chan.
• 2 ohms: 200 watts x 4 chan.
• AudioControl's Smart User DSP software inlcluded
• 30 Bands of graphic equalization

4
AudioControl D-4.800

800W RMS D-Series 4-Channel Amplifier with Digital Signal Processor

Special order

Ships at Later Date

$899.99 (14.44% off)
$769.99
Hide info
More info Item page
1 Special offer
  • Add a 100% Copper, True 4 Gauge Amp Kit and save 50%

Item Added to Cart

D-4.800 small

800W RMS D-Series 4-Channel Amplifier with Digital Signal Processor

$769.99

Keep Shopping

Belva BAK44 4-Channel 4 Gauge Amplifier Installation Kit

Complete 4-Channel CCA 4 Gauge Amp Kit with RCA Cables and Speaker Wire

$39.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$39.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl D-4.800.
AudioControl ACM-4.300

300W RMS ACM Series 2 ohm Stable 4-Channel Class-D Amplifier

ACM-4.300 main
Go to item page

300W RMS ACM Series 2 ohm Stable 4-Channel Class-D Amplifier

• 50 Watts RMS x 4 @ 4 ohms
• 175 Watts RMS x 2 @ 2 ohms
• 150 Watts RMS x 2 @ 4 ohms, Bridged
• Small Footprint for Flexible Mounting
• AccuBASS and GTO Signal Sense Built In
• Linkwitz-Riley Crossover
• Aluminum Heatsink
• Dimensions: 9.4" W x 3" L x 1.75" H

1
AudioControl ACM-4.300

300W RMS ACM Series 2 ohm Stable 4-Channel Class-D Amplifier

In stock

$399.99 (17.50% off)
$329.99
Hide info
More info Item page
3 Special offers
  • Save 20% off a 8-pack 8 gauge ferrule with heat shrink
  • Get A Free $50 Gift Card With Purchase!
  • FREE 8 Gauge 4 Channel Wiring Kit with Select Amps!

Item Added to Cart

ACM-4.300 small

300W RMS ACM Series 2 ohm Stable 4-Channel Class-D Amplifier

$329.99

Keep Shopping

Belva BAK84

Complete 8 Gauge Amplifier Wiring Kit with 4-Channel RCA Interconnects

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl ACM-4.300.
AudioControl ACM-2.300

300W RMS ACM Series 2 ohm Stable 2-Channel Class-D Amplifier

ACM-2.300 main
Go to item page

300W RMS ACM Series 2 ohm Stable 2-Channel Class-D Amplifier

• 75 Watts RMS x 2 @ 4 ohms
• 150 Watts RMS x 2 @ 2 ohms
• 300 Watts RMS x 1 @ 4 ohms
• Small Footprint for Flexible Mounting
• AccuBASS and GTO Signal Sense Built In
• Linkwitz-Riley Crossover
• Aluminum Heatsink
• Dimensions: 9.4" W x 3" L x 1.75" H

AudioControl ACM-2.300

300W RMS ACM Series 2 ohm Stable 2-Channel Class-D Amplifier

Special order

Ships at Later Date

$399.99 (17.50% off)
$329.99
Hide info
More info Item page
4 Special offers
  • Save 20% off a 8-pack 8 gauge ferrule with heat shrink
  • Save 50% on a Universal Wetsounds Remote Controller
  • FREE 100% Copper, True 8 Gauge Wiring Kit with Select Amps!
  • Save 50% on an 8 Gauge Amp Kit with Purchase!

Item Added to Cart

ACM-2.300 small

300W RMS ACM Series 2 ohm Stable 2-Channel Class-D Amplifier

$329.99

Keep Shopping

Belva BAK82

Complete 8 Gauge Amplifier Wiring Kit with 2-Channel RCA Interconnects

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl ACM-2.300.
Audio Control D-5.1300

5-Channel Amplifier with DSP (Digital Sound Processor)

D-5.1300 main
Go to item page

5-Channel Amplifier with DSP (Digital Sound Processor)

• 100 Watts RMS x 4 + 300 Watts x 1 @ 4 ohms
• 200 Watts RMS x 4 + 500 Watts x 1 @ 2 ohms
• AccuBASS® Processing
• MILCTM Maximum Input Level Control (Patent Pending
• CEA-2006 Compliant/Preamp Outputs/LPF
• GTOTM Signal Sense
• 6 preamp inputs
• 12"W x 8"D x 2.1"H

Audio Control D-5.1300

5-Channel Amplifier with DSP (Digital Sound Processor)

In stock

Only 1 Left!

$1249.99 (12.00% off)
$1,099.99

Item Added to Cart

D-5.1300 small

5-Channel Amplifier with DSP (Digital Sound Processor)

$1099.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add
NVX XIV65 V-Series Interconnect Cable

5m (16.40 ft) 6-Channel RCA Audio Interconnect Cable

$34.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Audio Control D-5.1300.
AudioControl D-6.1200

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

D-6.1200 main
Go to item page

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

• 125 Watts RMS x 6 @ 4 ohms
• 200 Watts RMS x 6 @ 2 ohms
• 400 Watts RMS x 3 @ Bridged
• Total Peak Power: 1200 Watts
• CEA-2006 Compliant/Preamp Outputs/LPF
• AccuBASS circruity for improved bass response
• GTO Signal Sensing Turn On

1
AudioControl D-6.1200

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

In stock

Only 1 Left!

$1249.99 (12.00% off)
$1,099.99
Hide info
More info Item page
3 Special offers
  • Get A Free $100 Dollar Gift Card With Purchase!
  • Get A Free $200 Dollar Gift Card With Purchase!
  • FREE 4 Gauge 5/6 Channel Wiring Kit with Select Amps!

Item Added to Cart

D-6.1200 small

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

$1099.99

Keep Shopping

Belva BAK46 6-Channel 4 Gauge Amplifier Installation Kit

Complete 6-Channel CCA 4 Gauge Amp Kit with RCA Cables and Speaker Wire

$59.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl D-6.1200.
AudioControl LC-1.1500

1500W Max (850W RMS) LC Series Monoblock Amplifier w/ AccuBASS

LC-1.1500 main
Go to item page

1500W Max (850W RMS) LC Series Monoblock Amplifier w/ AccuBASS

•850 Watts RMS x 1 @ 4 ohms
• 1500 Watts RMS x 1 @ 2 ohms
• Total Peak Power: 1500 Watts
• CEA-2006 Compliant/Preamp Outputs/LPF
• AccuBASS
• Aluminum Heat Sink

1
AudioControl LC-1.1500

1500W Max (850W RMS) LC Series Monoblock Amplifier w/ AccuBASS

Special order

Ships at Later Date

$869.99 (11.49% off)
$769.99
Hide info
More info Item page
2 Special offers
  • FREE Premium True 0 Gauge Wiring Kit with Select Amps
  • Save 50% off True 4 Gauge Wiring Kit with Select Amps

Item Added to Cart

LC-1.1500 small

1500W Max (850W RMS) LC Series Monoblock Amplifier w/ AccuBASS

$769.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX XLCA2

2 Channel Line Out Converter with xBOOST & 3-year warranty*!

$89.99

Add
NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft of V-Series 2-Channel RCA Audio Premium Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

$18.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl LC-1.1500.
AudioControl ACM-4.300 + Free 8 Gauge Amp Kit

300W RMS ACM Series 2 ohm Stable 4-Channel Class-D Amplifier

ACM-4.300, BAK82 main
Go to item page

300W RMS ACM Series 2 ohm Stable 4-Channel Class-D Amplifier

• 50 Watts RMS x 4 @ 4 ohms
• 175 Watts RMS x 2 @ 2 ohms
• 150 Watts RMS x 2 @ 4 ohms, Bridged
• Small Footprint for Flexible Mounting
• AccuBASS and GTO Signal Sense Built In
• Linkwitz-Riley Crossover
• Aluminum Heatsink
• Dimensions: 9.4" W x 3" L x 1.75" H

60
AudioControl ACM-4.300 + Free 8 Gauge Amp Kit

300W RMS ACM Series 2 ohm Stable 4-Channel Class-D Amplifier

In stock

$439.98 (23.86% off)
$334.99
AudioControl LC-6.1200 + Free $50 Gift Card

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

SonicElectronix-50-Gift-Card,LC-6.1200 main
Go to item page

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

• 750 Watts RMS x @ 4 ohms
•1,200 Watts RMS x 1 @ 2 ohms
• 400 Watts RMS Bridged, 4 ohm
• 6 Preamp Outputs
• AccuBASS bass control
• Aluminum Alloy Chassis
• 12" W x 7.95" L x 2.10" H

14
AudioControl LC-6.1200 + Free $50 Gift Card

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

In stock

$919.99 (16.30% off)
$769.99

Item Added to Cart

SonicElectronix-50-Gift-Card,LC-6.1200 small

1200W RMS LC Series Class-D 6-Channel 2-Ohm Stable Amplifier

$769.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$49.99

Add
Stinger SI4612 4000 Series Interconnect Cable

12 ft. 6-Channel 4000 Series Audio Interconnect Cable

$19.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl LC-6.1200 + Free $50 Gift Card.
AudioControl D-6.1200 + Free $100 Gift Card

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

D-6.1200, 100EGIFT main
Go to item page

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

• 125 Watts RMS x 6 @ 4 ohms
• 200 Watts RMS x 6 @ 2 ohms
• 400 Watts RMS x 3 @ Bridged
• Total Peak Power: 1200 Watts
• CEA-2006 Compliant/Preamp Outputs/LPF
• AccuBASS circruity for improved bass response
• GTO Signal Sensing Turn On

6
AudioControl D-6.1200 + Free $100 Gift Card

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

In stock

Only 1 Left!

$1349.99 (18.52% off)
$1,099.99

Item Added to Cart

D-6.1200, 100EGIFT small

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

$1099.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add
NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

$19.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl D-6.1200 + Free $100 Gift Card.
AudioControl D-4.800 Amplifier + Free High Quality NVX Amp Kit

800W RMS D-Series 4-Channel Amplifier with Digital Signal Processor

D-4.800, XKIT44 main
Go to item page

800W RMS D-Series 4-Channel Amplifier with Digital Signal Processor

• D-Series 4-Channel Amplifier with Digital Signal Processor
• 4 ohms: 125 watts x 4 chan.
• 2 ohms: 200 watts x 4 chan.
• AudioControl's Smart User DSP software inlcluded
• 30 Bands of graphic equalization

65
AudioControl D-4.800 Amplifier + Free High Quality NVX Amp Kit

800W RMS D-Series 4-Channel Amplifier with Digital Signal Processor

Special order

Ships at Later Date

$1049.98 (25.71% off)
$779.99
AudioControl LC-4.800

High-Power 4/3/2 Channel Amplifier with AccuBass

LC-4.800 main
Go to item page

High-Power 4/3/2 Channel Amplifier with AccuBass


• 2 Ohm: 200 watts x 4 chan.
• 4 Ohm: 125 watts x 4 chan.
• Bridged: 400 watts x 2 chan.
• AccuBASS® Processing
• Summable active speaker-level inputs (6 channels) for OEM integration
• Line-level and Speaker-level (high-level) inputs
• MILC™ Source Clip Detection
• Solid One-Piece Aluminum Chassis
• GTO™ Signal Sense

2
AudioControl LC-4.800

High-Power 4/3/2 Channel Amplifier with AccuBass

OUT OF STOCK

$629.99 (12.70% off)
$549.99

Item Added to Cart

LC-4.800 small

High-Power 4/3/2 Channel Amplifier with AccuBass

$549.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$49.99

Add
NVX XIV45 4-Channel RCA Audio Interconnect Cable

5 Meters (16.4 ft.) 4-Channel RCA Audio Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

$23.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl LC-4.800.
AudioControl ACM-1.300

300W RMS ACM Series 2 ohm Stable Monoblock Class-D Amplifier

ACM-1.300 main
Go to item page

300W RMS ACM Series 2 ohm Stable Monoblock Class-D Amplifier

• 175 Watts RMS x 1 @ 4 ohms
• 300 Watts RMS x 1 @ 2 ohms
• Small Footprint for Flexible Mounting
• AccuBASS and GTO Signal Sense Built In
• Linkwitz-Riley Crossover
• Aluminum Heatsink
• Dimensions: 9.4" W x 3" L x 1.75" H

2
AudioControl ACM-1.300

300W RMS ACM Series 2 ohm Stable Monoblock Class-D Amplifier

OUT OF STOCK

$329.99 (15.15% off)
$279.99

Item Added to Cart

ACM-1.300 small

300W RMS ACM Series 2 ohm Stable Monoblock Class-D Amplifier

$279.99

Keep Shopping

Belva BAK82

Complete 8 Gauge Amplifier Wiring Kit with 2-Channel RCA Interconnects

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl ACM-1.300.
Audio Control ACX-300.1

ACX Series All-Weather 300W Monoblock Audio Marine Amplifier

ACX-300.1 main
Go to item page

ACX Series All-Weather 300W Monoblock Audio Marine Amplifier

• 175 Watts RMS x 1 @ 4 ohms
• 300 Watts RMS x 1 @ 2 ohms
• Total Peak Power: 600 Watts
• CEA-2006 Compliant
• AccuBASS®

Audio Control ACX-300.1

ACX Series All-Weather 300W Monoblock Audio Marine Amplifier

OUT OF STOCK

$329.99 (15.15% off)
$279.99

Item Added to Cart

ACX-300.1 small

ACX Series All-Weather 300W Monoblock Audio Marine Amplifier

$279.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX XLCA2

2 Channel Line Out Converter with xBOOST & 3-year warranty*!

$89.99

Add
NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft of V-Series 2-Channel RCA Audio Premium Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

$18.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Audio Control ACX-300.1.
AudioControl D-6.1200 Amplifier + Free High Quality NVX Amp Kit

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

D-6.1200, XKIT46 main
Go to item page

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

• 125 Watts RMS x 6 @ 4 ohms
• 200 Watts RMS x 6 @ 2 ohms
• 400 Watts RMS x 3 @ Bridged
• Total Peak Power: 1200 Watts
• CEA-2006 Compliant/Preamp Outputs/LPF
• AccuBASS circruity for improved bass response
• GTO Signal Sensing Turn On

34
AudioControl D-6.1200 Amplifier + Free High Quality NVX Amp Kit

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

Special order

Ships at Later Date

$1394.97 (20.43% off)
$1,109.99

Item Added to Cart

D-6.1200, XKIT46 small

1200W RMS 4 ohm Stable 6-Channel Class-D Amplifier w/ Digital Signal Processing

$1109.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add
NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

$19.99

Add

Don't see the accessory you're looking for?
View all available accessories for the AudioControl D-6.1200 Amplifier + Free High Quality NVX Amp Kit.

Related Categories


AudioControl EQs, Signal & Sound Processors AudioControl EQs, Signal & Sound Processors

Find a quality line output converter, digital sound processor, EQ, crossover or bass enhancer in here.

AudioControl Marine Amplifiers AudioControl Marine Amplifiers

Enhance the sound on your boat by adding an amplifier to your marine audio system. These marine amps are the perfect way to get louder, bigger, and clearer sound quality on your boat. These marine amplifiers can be great for standard boat speakers, tower speakers, and even some marine PA systems. Each amp is specially treated and engineered to function in the same wet, salty environment that boats are in.

    clear all items