Access exclusive offers, news and more.
700W Peak 350W RMS N-Series V2 10" Dual 4-Ohm Car Subwoofer Package
• 350 Watts RMS / 700 Watts Max
• Impedance: Dual 4-Ohm
• Ultra-Light Non Pressed Paper Cone
• Custom Blended Foam Surround
• 2” High-Temperature Aluminum Voice Coil
• 750W x 1-Channel @ 4 ohms
• 1500W x 1-Channel @ 2 ohms
• Total Peak Power: 1500 watts
• Class A/B 2 ohms Stable Monoblock
The NVX N-Series subwoofers offer top-notch sound quality at an entry-level price. The NSW104V2 is a great multi-purpose sub that has been engineered to meet the highest audio standards. The stiff, ultra-light non pressed paper cone allows the N-Series subs to give you accurate and responsive low-end even when you have your system blasting. The custom-blended high roll foam surround allows for greatly improved excursion for further improved sound quality. The 2" dual 4-ohm high-temperature aluminum voice coil gives you a wide array of Ohm load wiring options for different applications. With an RMS Power Range of 200-350 watts, the NSW104V2 requires less power to operate efficiently without losing bass quality.
Continuing with the excellent engineering is a stamped steel basket that provides exceptional rigidity while minimizing any unwanted distortion. The N-Series subwoofers also include spring-loaded, chrome-plated push terminals that provide an easy and secure speaker wire connection. NVX's mission was to create an exceptional subwoofer at an entry-level price without sacrificing the quality and sound that the consumer deserves. They have succeeded!
We’re all about the details here at NVX. That's why we include a rubber trim ring gasket with our N-Series subwoofers. The trim ring provides a tight seal against the sub and the box it is being mounted to, in order to prevent air pressure from passing between the two.
We’re all about getting the most bang for our buck, a key reason why we chose to include high-roll foam surround technology in the N-Series woofers. The surround itself is constructed with high excursion foam, which keeps the inward movement of the surround perfectly symmetrical with the outward movement.
Our custom basket offers several distinct advantages over traditional designs. We purposefully chose an especially open basket to improve airflow to reduce compression of the motor structure for both improved cone control as well as reduced back-wave interference.
The stout 2" high-temperature voice coil is constructed from a copper wire wrapped around an aluminum former. This industry-standard design is powerful enough to readily drive the cone with strict linear control, yet at the same time remains efficient enough for the compact, space-saving magnet structure.
We chose a highly magnetized single stacked Ferrite magnet for the motor structure in the new N-Series. This magnet allows for greater power handling and voice-coil control during high excursion limits.
After testing scores of different cone materials, we decided on a custom blend of fine Ultra-Light Non-Pressed Paper fibers. This stiff yet lightweight material produces spectacularly accurate bass with a rich, natural tonal quality prized by audiophiles. The smooth matte finish of the cone offers a sleek, modern accent to the interior of any car.
At NVX we understand that the components of a subwoofer must work in harmony to achieve sonic excellence and that a subwoofer is only as reliable as its weakest link. There is perhaps a no better example of our relentless attention to detail than the unique attachment method of our tinsel leads. Whereas the leads of most subwoofers are simply glued atop the spider, ours are glued at the basin of each fold in the spider with enough slack on top for an unrestricted excursion.
We didn't even skimp on the magnet boot for our N-Series subwoofer. Besides looking better than a bare magnet the rubber boot protects the magnet from chipping and possible corrosion that can affect magnets exposed to the elements.
NVX NSW104 Version 2 (NSW104v2)
700W Peak 350W RMS N-Series V2 10" Dual 4-Ohm Car Subwoofer
8 Gauge Premium (CCA) Copper Clad Aluminum Complete 2-Channel Amplifier Wiring Kit with RCA for Amplifiers up to 600 Watts - RED
(newest, current model)
(previous model, replaced by NVX NSW104v2with Belva BXA15001 and Amp Kit)
NSW104V2, BXA15001, BAK82
Internal Product ID:
Nice package, quality wire but could more end connectors for the larger wire.
122found this helpful.
It's exactly what you need for your car amp installation. I bought this kit with Kenwood KAC-1502S amp for 75 bucks. Good deal from Sonic Electronix.
116found this helpful.
Don't know what the other guy is talking about.
This kit was awesome and included with my package that I bought. In comparison to others for the same price, there is simply not a comparison and the other review is just wrong on so many levels I felt compelled to write this.
The reality is there are a lot of real shoddy amp kits and wire as a whole being used in car audio in terms of cheap amp kits that have over-insulating wires and fake gauge ratings, huge amounts of aluminum, lousy RCA cables, fuse holders and other accessories. BUT and a BIG BUT, this kit excels in those areas where others fall flat on their face. I have bought a few inexpensive 8 gauge kits in my day and XScorpion, Raptor, Install Bay and others haven't even given me the 8 gauge of wire that I paid for, and in some cases gave me wire that heated up to a dangerous level due to the actual make up of the wire.
I also literally laughed when I see that the other reviewer was intending to use spade terminals to connect his amp power and ground wire... It is for the SPEAKER wire knucklehead :-). I am an installer and the smaller accessories work just fine when you use them correctly. Most amps will still work with them when used with the speaker wire. Of course one can be used for the remote wire connection to the amp and the other end with the butt connector being used to connect to the stereo. The funny thing is, if you do not need them, who cares? It is like ordering this kit for a compact car or single cab pickup. You will not use all of the power wire for these applications, so do you complain that the manufacturer gave you extra wire? That just made me laugh.
Now, onto the other accessories. The AFS fuse and holder that are included are so far superior to others in this price range and the amount of copper (albeit CCA) is much better than others in the price range. Lastly, the RCAs included are awesome for the price. I cannot find ANYTHING to complain about here for $21.99.
All in all, you will not get a better value for the money.
103found this helpful.
Great kit for the cost
Very nice kit for $18.
Wire seems adequately thick. Good quality fuse (not AGU) and fuse holder. RCA's feel durable. Decent assortment of accessories. All together a solid budget kit IMO.
107found this helpful.
I used this kit to install a 2 channel Boss amp. The quality of the pieces in this kit is five stars, but I'm giving it 4 because it is my belief that to do a clean install you need (4) 8 gauge terminals (one at the batt, one at the amp, one at ground, one at the amp), not just two. I had to spend an extra six bucks at Orchard for the extra terminals, but since the cost of the kit here at Sonic was only $20 at the time, it was still a good deal.
100found this helpful.
Great wiring kit
works great on my MB Quart 2x100 watt amp.
99found this helpful.
Good kit for basic setups. Using it right now in my mothers system powering a simple 12. Could handle more if needed.
Pros: Handles power, Wires are HQ, More copper than rubber, Wires are good length, Fuse is HQ, Comes with lots of ties and rubbers.
I would recommend this kit to anyone who has a simple system. All around good kit.
105found this helpful.
Good product for the price
Good wiring package, good quality fuse holder and wires, I would like more connectors on it and maybe some tube for the power wire, but overall is a good kit.
103found this helpful.
Great kit for the price. the price is good. Long wires.
98found this helpful.
Worked very well for the money, great value for my system! Only thing that kept me from giving this 5 stars across the board is the design of the fuse holder and how you have to change/connect the fuse, minimal complaint.
96found this helpful.
This product is temporarily out of stock. May we recommend...
MTX Audio TNP212D2 Terminator Dual Subwoofer Package + Amplifier
• 1200W Peak (2 Subs)
• 400W RMS (2 Subs)
• 48oz. Magnet
• Terminator Series Class D Monoblock Car Amplifier
• Heavy 5/8" MDF Construction
• Black Carpeting
Belva BPKG212v2 Complete Amplified Bass Package
• Works with both Factory and Aftermarket Audio Systems
• Dual 12" Belva Subwoofers
• Monoblock Amp with Bass Knob
• Ported Enclosure
• Complete Amp Wiring Kit
• 12" Amplified Loaded Subwoofer System
• 500 watts RMS
• Built-In Class D Amplifier
• Variable Bass Boost
• Speaker-Level Inputs
• Wired Remote Bass Level Control
• XED Series Bass Package
• Two 12" Subwoofers with 2" Voice Coill
• 400W RMS Monoblock Amplifier
• Carpeted and Embroidered Enclosure
• Complete Direct Fit Audio System Upgrade
• 2" Component Tweeters
• 8" Powered Subwoofer
• Universal Power Pack Amplifier
Save up to 10 different vehicles in your garage