JL Audio XD600/6v2 with Amplifier Wiring Kit

General Features:

• XDv2 Series Class D 6-Channel Amplifier
• RMS Power Rating @14.4V:
• 4 ohm: 75 watts x 6 chan.
• 2 ohm: 100 watts x 6 chan.
• Bridged 4 ohm: 200 watts x 3 chan.
• RMS Power Rating @12.5V:
• 4 ohm: 60 watts x 6 chan.
• 2 ohm: 90 watts x 6 chan.
• Bridged 4 ohm: 180 watts x 3 chan.
• NexD High Speed Switching Class D Technology
• Wired HD-RLC remote level control available, sold separately
• LED power (green), over-current (yellow) and protect (red) indicators
• Advanced Rollback Protection
• Differential Balanced RCA Input
• Pass-through preamp RCA outputs
• Selectable turn-on modes: REM / Offset / Signal
• +12 V Remote Turn-On: Traditional remote lead wire, from headunit
• DC Offset-Sensing: On/Off by detecting a very small DC signal (high-level signal only)
• Signal-Sensing: On/Off by detecting a full-range audio signal at left-channel input (high-level signal only)
• Speaker level inputs via RCA, JL Audio XD-CLRAIC2-SW required
• Heavy duty aluminum alloy heat-sink for extreme heat dissipation
• 3-way protection circuitry (thermal, overload, and speaker short protection)
• Detented, Calibrated Filter Freq. Potentiometer
• State-variable, 12dB/octave Butterworth Crossover
• Selectable input mode: 2 Ch. / 4 Ch. / 6 Ch.
• Input sensitivity:
• Low level: 800mV - 8V
• High level: 200mV - 2V
• Frequency Response: 12 - 22,000 Hz
• Total Harmonic Distortion (THD): <1%
• Signal to Noise Ratio: >104 dB
• Damping Factor @4 ohm: >150 / 50 Hz
• Selectable Filter Mode: Off / HP / LP
• Variable cutoff filter: 50 - 500 Hz, 12 dB/octave
• Fuse Rating: 50A x 1 inline (not supplied)
• 4 gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
• Weight: 6.00 lb
• Dimensions: 7.09"W x 10.23"L x 2.05"H
• Authorized Internet Dealer
• 2 Year Manufacturer's Warranty

Product Details:

• 4 Gauge 5/6-Channel X-Series Complete Amplifier Installation Kit
• Designed for car audio systems up to 1500 watts RMS
• Made from 100% Oxygen-Free Copper (OFC)
• Tinned conductors for corrosion resistance
• Pre-installed black nylon mesh covering protects the power wire from damage
• Solid brass and satin chromed ANL/Mini-ANL fuse holder offers ideal protection for high-powered systems
• Pre-terminated seamless power and ground ring terminals provide reliable performance
• Full spec power and speaker wire meet or exceed American Wire Gauge standards
• CEA-2015 and BC5W2 compliant
• V-Series RCA Interconnect Cable
• Shielded noise-rejecting coaxial construction provides protection against interference
• Split-tip silver-plated ends offer high-quality performance
• Molded ends equipped with colored channel identifiers for easy recognition
• Twisted-pair construction featuring two conductors per channel
• Includes an assortment of wire termination hardware and cable ties
• Authorized Internet Dealer
• 1-year Manufacturer's Warranty

Kit includes:

1. 17 ft. Frosted Blue 4 gauge power wire with seamless crimp ring terminal
2. 3 ft. Frosted Black 4 gauge ground wire with seamless crimp ring terminal
3. 17 ft. Clear 18 gauge remote lead wire
4. 60 ft. Frosted Black/Blue 16 gauge speaker wire
5. One 16.4 ft. 4-channel dual twisted construction RCA interconnect Cable (NVX XIV45)
6. One 16.4 ft. 2-channel dual twisted construction RCA interconnect Cable (NVX XIV25)
7. One NVX XMANL04 ANL/Mini-ANL Fuse Holder with 100 amp Mini-ANL fuse
8. One Black rubber firewall grommet
9. Two 4 Gauge Nickel Plated spade terminals
10. Four 18 Gauge Spade terminal
11. Two 18 Gauge Red butt connectors
12. Four 16 Gauge quick disconnect
13. Five 16 Gauge Nickel Plated spade terminals
14. Two Heat Shrink tubes with the NVX logo
15. Ten 6" Black zip ties