Diamond Audio 4-Channel Amplifiers at Sonic Electronix

Diamond Audio 4-Channel Amplifiers

Diamond Audio is a premier manufacturer of 4-channel amplifiers.
Filters
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

The lowest impedance the amplifier will handle when it is not bridged.
The lowest impedance the amplifier will handle when it is bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
listview icon
gridview icon
Diamond Audio MICRO4V2

4-Channel Micro Class-D Amplifier 600W RMS

MICRO4V2 main
Go to item page

4-Channel Micro Class-D Amplifier 600W RMS

• 4-Channel Micro Class-D Amplifier
• 80W RMS x 4 @ 4Ω / 150W RMS x 4 @ 2Ω / 300W RMS x 2 @ 4Ω Bridged
• Ultra-compact, high density aluminum alloy chassis provides superior thermal stability
• Four layer, glass epoxy circuit board for enhanced performance and reliability
• Full Range Class D amplifier technology

Diamond Audio MICRO4V2

4-Channel Micro Class-D Amplifier 600W RMS

Special order

Ships at Later Date

$379.99 (2.63% off)
$369.99

Item Added to Cart

MICRO4V2 small

4-Channel Micro Class-D Amplifier 600W RMS

$379.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX XIV45 4-Channel RCA Audio Interconnect Cable

5 Meters (16.4 ft.) 4-Channel RCA Audio Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

$23.99

Add
NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

$29.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Diamond Audio MICRO4V2.

Related Categories


Diamond Audio Marine Amplifiers Diamond Audio Marine Amplifiers

Enhance the sound on your boat by adding an amplifier to your marine audio system. These marine amps are the perfect way to get louder, bigger, and clearer sound quality on your boat. These marine amplifiers can be great for standard boat speakers, tower speakers, and even some marine PA systems. Each amp is specially treated and engineered to function in the same wet, salty environment that boats are in.

Diamond Audio 4-Channel Amplifiers Information

A 4 channel car amplifier from Diamond Audio will provide your vehicle with the power it requires. These amps can operate four channels and Diamond Audio is a leader in amplification solutions. Power your speakers with a Diamond Audio 4-channel amplifier for a great all-around sound.
    clear all items