• RMS Power: 400W x 1 @ 4 ohms, 750W x 1 @ 2 ohms, 1200W x 1 @ 1 ohm
• Total Peak Power: 2400W
• Variable Low Pass Filter
• Dimensions: 8.9" W x 14.2" L x 2.03" H
Belva BAK42BK (Black)
Complete 4 Gauge Amplifier Wiring Kit With 2-Channel RCA Cable (CCA Wiring)
NVX SDBBP40 Premium Stealth Black
Premium Sound Deadening Bulk Pack 40 Square feet (Entire Car), Ten 18" x 32" Sheets (91mil Thick)
Sound damping can be a very beneficial accessory to reduce noise and vibration. To take full advantage of this soundproofing, read these instructions carefully and follow them till the end. It’s important to familiarize yourself with all the details to install the sound damping correctly. Incorrect installation will result in less than desirable results.
The first step is to decide which location in your car you want to insulate. These locations include the floorboards, roof, door panels, trunk or firewall. We recommend soundproofing all metal surfaces for maximum sound deadening performance. Next, refer to your vehicle’s service manual for information on how to dismantle the trimming panels. Be careful when removing the panels to avoid breaking the fixing clips.
Once the trimming is dismantled, remove the remainder of the factory insulation if it is damaged. If it is still intact, there is no need to permanently remove it. Next, you need to properly clean, dry and degrease the prospective surface. Sound deadening won't adhere properly if applied to a wet or dirty surface. Use a metal surface cleaner or degreaser along with a dry, clean rag. Make sure to use gloves and apply the degreaser in a well-ventilated space.
For this step, measure the prospective surface you are going to treat. To make things easier, make a template of the appropriate size on a large sheet of paper and then transfer it to the damping material. That will make it easier to install it more accurately and avoid wasting material. Use a utility knife to cut the desired shape and size. Be careful and use gloves to protect your hands.
Place a sheet of sound damping to the surface without removing the protective film. If it covers the surface properly, you are ready to install it. Gradually remove the protective paper film as you apply it to the surface for better adhesion. Once on the surface, press it down firmly until it is set in place. Flatten it with your hands to avoid unnecessary air bubbles. Use a rolling tool like the NVX SDRLR1 to press the mat down to the metal surface. Go across the entire surface with the roller to ensure that the sheet is installed properly.
Once all sound deadening is in place, simply reinstall all trim pieces and carpet back to its original placement. Now you are ready to enjoy higher sound quality with fewer vibrations.
(newest, current model)
(previous model, replaced by MTX XTHUNDER1200.1 1200w RMS Mono Car Stereo Amplifier+Amp Kit+Sound Deadening)
This item is currently not eligible for our low price guarantee. This may be due to supply constraints, manufacturer restrictions, or another reason. We're always here to help you get the best price possible so give us a call or email today. Our experts will do their best to build the system that works for you within the rules.
Overall rating distribution
By feature average rating
March 8, 2015
I like the wire kit I got with my amp it seems to be holding up goo it handles the power of the amp I got but I would of gave it 5 stars all the way around but I wold of like the ground at less 2 more feet for good use but over all its a nice kit
March 22, 2015
I run 2 12inch audiobahn exursions on this amp and it pushes them very well. The size is perfect not to big and fits right unerneath the seat or small space. The best part is it stays pretty cool even after running most the day.
March 2, 2015
Works but ...
At low volume it sounds as if the subs turned off. Sq is fine but a horrible turn off pop on the subs. Gains have to be turned way past where any amp I had were. You also have to have the bass boost turned up just to get any low end out of the subs at low volume.
Controls on the ends are fine and work as intended.
Comes with the bass knob for the front . Maybe I got a bad one.. Expected more than what I have out of this company. Feels nice and heavy solid construction .
June 30, 2015
Nothing short of Epic
I admit that i was a bit hesitant to pick this guy up. I could get the same power from cheaper amplifiers, but MTX has been around for years and their products have always been in the SPL scene, so I went with my gut on this on. NO REGRETS!! Right out of the box, the amplifier is clearly build right, hefty, and with high quality components. Beyond that, the aesthetics are nothing special, But I think that speaks volumes! Why waste money on putting a skull with pretty lights on the chassis, and not put that towards developing a proper amplifier. Thats what we got here.
I used proper 0 Gauge OFC wiring to make sure the amp gets the power it needs, hooked up to an XS Power battery, and an AudioControl Epicenter. For having a cheesy name like "Thunder" , you really do get that.
Best selling similar products
• 300 Watts Max x 2 @ 4 ohms
• 600 Watts Max x 2 @ 2 ohms
• 1200 Watts Max x 1 @ 4 ohm Bridged
• Total Peak Power: 1200 Watts
• Pro- Fi™ High Speed MOSFET power supply
• Variable high-pass filter: 120 - 3000 Hz, 12 dB/octave
• Variable low-pass filter: 50 - 250 Hz, 12 dB/octave
• Dimensions: 11.4"W x 12.7"L x 4"H
• The size of a postcard with 400 Watts True RMS Output!
• • MVP Series 4-Channel Micro Class D Amplifier
• 50W x 4-Chan. @ 4 ohms
• 100W x 4-Chan. @ 2 ohms
• 3-Way System Protection
• 4/3/2/1 Channel Operation
• 8 Gauge Power and Ground Inputs
• Extremely Small Footprint!
• 8 Gauge 4-Channel Complete Amplifier Installation Kit
• For Car Audio Systems Up To 600 Watts RMS
• Silver-Tinned 100% Virgin Copper
• 4-channel RCA Interconnect Cable
• RMS: 80 Watts x 4 @ 4 ohms, 150 Watts x 4 @ 2 ohms, Bridged: 300 Watts x 2 @ 4 ohm
• Total Peak Power: 1000 Watts
• Class D IR Chipset with DirectFET Power Mosfet Output
• Wired remote bass level control included
• Ultra Compact High Density Aluminum Alloy Chassis
• Dimensions: 4.02" W x 8.70" L x 1.40" H
• 4-Channel Class D
• NexD Switching Technology
• Compact and Powerful
• Copmlete Signal Processing Sections
• 100 Watts RMS x 6 @ 4 ohms
• 150 Watts RMS x 1 @ 2 ohms
• CEA-2006 Compliant/Preamp Outputs/LPF
• Micro Amp
• 12.9"W x 4.4"L x 1.7"H
Internal Product ID: