Wet Sounds STEALTH AS-10
500W Amplified Single 10" Stealth Series Sealed Subwoofer Enclosure w/ Built-In Class D Amplifier
- 500 W Single 10" Sealed Subwoofer Enclosure with Built-In Amplifier
- Power Handling:
- Peak: 1000 W
- RMS: 500 W
- Preloaded with single 10" Subwoofer
- Built-in high efficiency Class D amplifier
- Easy Plug & Play connection with STEALTH Sound Bars, or any other system
- Sealed enclosure with black paint finish
- Auto or manual turn-on function
- Aluminum mesh grille
- Stainless steel mounting hardware included
- Enclosure Dimensions: 11.5" D x 14.74" W x 12.75" H
- Authorized Internet Dealer
- 1-year Manufacturer's Warranty
- High Excursion subwoofer driver
- Frequency Response: 20 - 250 Hz
- Class D amplifier
- Variable Low Pass Cross Over: 50 - 200 Hz
- Variable Bass Boost: 0 - 12 dB
- Thermal and over/under voltage protection
- 10" Sealed Subwoofer Enclosure
- Rotationally Molded Polyethylene Housing
- Stronger, lighter, and more durable than the fiberglass
- Black paint finish
Check out the STEALTH AS-10 Owner's Manual
An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.
Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.
Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.
It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.
The RMS power rating is more accurate, and we recommend using it for product comparison.
RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.
The RMS output figure is much more accurate than the peak rating when comparing products.
A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.
When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.
The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.
- RMS Power
- Signal-to-Noise Ratio
This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.
Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.
Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.
Sealed - Sealed boxes are those that have no holes or vents in it. The only hole in a sealed box is where the subwoofer is installed. Smaller sealed boxes require more power than a larger sealed box. They provide a tight, accurate bass, while the larger sealed enclosures provide a "boomier" and louder bass.
Ported / Vented - Ported/Vented Enclosures provide an even boomier, louder bass, but less accurate then a small, sealed box. Ported enclosures typically require more airspace per sub and also less power output from an amplifier to perform correctly.
Bandpass - Bandpass enclosures make subwoofers perform efficiently, but loose. The bass is not as "boomy" as a ported enclosure nor as punchy as a sealed enclosure. Bandpass enclosures work well with lower to mid-level subwoofers.
Specials with this Item
Warranty and Return Policy
Trunk Kit - 20 Square Feet of Sound Dampening Material (Five 18" x 32" Pieces)
Your Price $59.99
20 ft. Trunk Kit with (5) Dynamat Extreme 18" x 32" Pieces
Your Price $177.99
20.8 sq.ft Damping Material - (10 pk - 12-1/2" x 24" x 2mm )
Your Price $101.99
Internal Product ID
Wiring Diagram Legend
Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.