300W RMS Punch Series Class-BR 2-Channel Amplifier
• 100 watts x 2 channel @ 4 ohms
• 150 watts x 2 channel @ 2 ohms
• Bridged: 300 watts x 1 channel @ 4 ohms
• Total RMS Power: 300 watts
• Class BR 2 ohms Stable 2-Channel Amplifier
Make adjustments with ease with 0dB to +18dB bass boost with this bass knob built specifically for Rockford Fosgate Amplifiers. This offer cannot be combined with any other coupons or offers.
Rockford Fosgate Punch PBR300X2
100% off
$249 99
$29 99
Priced separately $279 98
Promo Savings of $29 99
Total price:
$249 99
• 100 watts x 2 channel @ 4 ohms
• 150 watts x 2 channel @ 2 ohms
• Bridged: 300 watts x 1 channel @ 4 ohms
• Total RMS Power: 300 watts
• Class BR 2 ohms Stable 2-Channel Amplifier
To achieve higher efficiency with lower distortion, Rockford's BR topology combines, Cycle-by-Cycle, an indirectly coupled high/low voltage rail linear topology with a switched high/low voltage linear rail topology. This combination yields an unsurpassed power density (watts per cubic inch). In addition, this patented technology allows the chassis design to be much smaller than traditional sized amplifier - 1.53" x 4.25" x 6.75" - making this amp a great solution for smaller stealth installations, motorcycles and recreational vehicles. In fact, now, with the introduction of the Rockford Fosgate RFKHD9813, installing the PBR300X2 into select 1998 - 2013 Harley Davidson motorcycles has never been easier. With unparalleled technology, flexible installation options, and big power from such a small footprint Rockford Fosgate has ensured that everyone can put a little Punch in any system.
The Punch EQ on-board equalization circuit helps correct the acoustical deficiencies often found in car audio systems. These deficiencies were researched and graphed out by none other than Jim Fosgate himself. From that forward thinking approach, we now have the Punch EQ2. When accompanied by the Optional Remote Punch EQ, the user has full control of a variable bass boost centered at 45 Hz.
MEHSA3 is a proprietary process that yields up to five times better heat transfer than traditional FET mounting techniques, using the exact same components. A multi-layer insulated metal substrate operating with minimal thermal resistance spreads heat both downward & outward to quickly dissipate heat from each device across the heatsink. This process allows Rockford Fosgate to squeeze more watts per cubic inch from every output device as well as provide consistent thermal stability. The higher power handling results in a 20% reduction in thermal impedance.
An industry-leading manufacturing process, DSM utilizes high-speed robotics, high-quality 1% tight-tolerance parts and large board traces. The discrete components are laser etched to meet a particular value and a very low tolerance. This lower tolerance improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature. These superior components are used by aerospace, automotive, and cellular manufacturers.
Check out the Punch PBR300X2 Owner's Manual
Check out the Class-BR Amplifier Installation Advisory From Rockford Fosgate
Internal Product ID:
43424
| 5 star |
|
90% |
| 4 star |
|
10% |
| 3 star |
|
0% |
| 2 star |
|
0% |
| 1 star |
|
0% |
| Durability | ||
| Value | ||
| Features | ||
| Design | ||
| Usability |
Great Little Amp!
I installed this amp on my Harley Street Glide to drive two 6.5" Polk MM651 2ohm fairing speakers. I'm pushing over 150 watts per channel with this beast! The amp fits great and sounds incredible! I don't believe you will find better sound quality and power in such a small package for the price!
100
found this helpful.Rockford Fosgate PBR 300x2
This is one kick little amp, very small and lots of punch! it drives 4-Rockford 6.5" on my Harley davidson and I'm going to purchase one more to drive a set of 6x9 in my saddle bags! perfect crisp clean and did I mention LOUD! best bang for the buck and fast shipping.
Go get yourself one.
Rich
98
found this helpful.Harley Davidson
I purchased two of these for my 2012 Ultra. I have one on top of the radio feeding the front speakers and one located in the trunk feeding the speakers in the lowers. I picked this model for the ability to be 2 ohm stable and produce 150 watts per channel. They do run hot and will need air around them. They blow away all the other amps I have used on bikes up to this point. Be prepared to piss off the cars around you even at 70. My friends tell me you can hear me very clear several blocks away. Running Polk MM 6 1/2 for speakers.
96
found this helpful.excellent performance
Awesome little amp for a great price.
Fast shipping and a pleasure dealing with reps.
97
found this helpful.This little Amp rocks
Put in my sxs,uses very little power can run off stock battery for hrs & always starts right up,built a lexan cover around it (to keep dry & clean) w/ a 70mm fan in it & it bearly gets warm, use (2) 6x9 speakers,its crystal clear.& loud.
96
found this helpful.Great little amp
The size of this amp gives you the ability to install it were there in not much room,the amp has enough power for my door speakers
92
found this helpful.Awesome service!!
Big power for such a small unit. Quick delivery and awesome service.
94
found this helpful.good value
I own two rockford fosgate pbr300x2, well built amp, easy to install in roadglide fairing after making braket easy to wire up to radio. Sounds great.
92
found this helpful.The best small amp with true power
I would Recommend this to anybody who's looking for a good amp with small space this amp is a true 300 watts I'm glad I found this amp I am very happy with it
90
found this helpful.Rockford Fosgate PBR300X2
I purchase this amp to drive some Polk speakers and boy does. Becasue of it size it was easy to install and was even easier to adjust. For the price I think it was a great buy. Thanks Sonic and Rockford!
89
found this helpful.
Controls bass level and frequency and monitor voltage
Flush Mount & Universal via RCA. Works with any amp, controls your bass output
The XLOC22X helps you easily integrate with your factory or aftermarket stereo system
16.4 ft 2-Channel RCA Audio Interconnect Cable with Twisted Pair Construction
Great for isolating a second batter making it dedicated to the stereo system
Great for isolating a second batter making it dedicated to the stereo system
Does not create a voltage drop to the second battery like conventional isolators
Spade Terminals • 10 Gauge • 1 Red & 1 Black • Nickel Plated
Best selling similar products
• 100 watts x 4 channel @ 4 ohms
• 160 watts x 4 channel @ 2 ohms
• Bridged: 320 watts x 2 channel @ 4 ohms
• Total RMS Power: 600 watts
• Class D 2 ohms Stable 4-Channel-Channel Amplifier
$144.99
• 670 watts x 1 channel @ 4 ohms
• 1100 watts x 1 channel @ 2 ohms
• 1500 watts x 1 channel @ 1 ohm
• Total RMS Power: 1500 watts
• Class D 1 ohms Stable Monoblock Amplifier
$179.99
• 500 watts x 1 channel @ 4 ohms
• 850 watts x 1 channel @ 2 ohms
• 1200 watts x 1 channel @ 1 ohm
• Total RMS Power: 1200 watts
• Class D 1 ohms Stable Monoblock Amplifier
$149.99
This item is frequently compared to these items
• Remote wired bass/treble boost
• Remote Punch EQ Wired Bass Boost for Punch Amplifiers
• 0dB to +18dB bass boost @ 45Hz.
• 0dB to +12dB treble boost with hinge filter between 1kHz to 20kHz.
$29.99
