Garage
Shop

JL Audio Class D Amplifier + FREE Infinity 12" Reference Series Subwoofer

JL Audio XD300/1v2 300W XDv2 Series Monoblock Class D Subwoofer Amplifier + Infinity 1262W300W 12" Reference Series Dual 4 ohm Subwoofer

JL Audio
Shop all JL Audio
EXCLUSIVE
highlight-star-icon

• 300 W x 1 @ 2 ohm
• High-Gloss Polypropylene Woofer
• Large-Roll Rubber Surround
• 2" Voice Coil
• Vented Pole Pieces
• Progressive Spider
• NexD™ Switching Technology
• Dual-Range Differential Balanced Input Section
• Advanced Rollback Protection
• Selectable Low-Pass Filter Slope: 12 dB or 24 dB
• Detented, Calibrated Filter Freq. Potentiometer

Learn more about the xd3001v2_1262w

We apologize

This item has been discontinued

Description


JL Audio brand icon

Authorized dealer

JL Audio XD300/1v2

300W RMS XDv2 Series Monoblock Class D Subwoofer Amplifier w/ High-Speed NexD Switching
Quantity: 1

General Features:

  • XDv2 Series Class D Monoblock Amplifier
  • RMS Power Rating @14.4V:
    • 4 ohms: 200 watts x 1 chan.
    • 3 ohms: 250 watts x 1 chan.
    • 2 ohms: 300 watts x 1 chan.
    • 1 ohm: ----------N/A----------
  • RMS Power Rating @12.5V:
    • 4 ohms: 160 watts x 1 chan.
    • 3 ohms: 210 watts x 1 chan.
    • 2 ohms: 270 watts x 1 chan.
    • 1 ohm: ----------N/A----------
  • NexD#8482; High Speed Switching Class D Technology
  • Wired HD-RLC remote level control available, sold separately
  • LED power (green), over-current (yellow) and protect (red) indicators
  • Advanced Rollback Protection
  • Dual-Range Differential Balanced Input Section
  • Buffered pass-through preamp RCA outputs
  • Selectable turn-on modes: REM / Offset / Signal
    • +12 V Remote Turn-On: Traditional remote lead wire, from headunit
    • DC Offset-Sensing: On/Off by detecting a very small DC signal (high-level signal only)
    • Signal-Sensing: On/Off by detecting a full-range audio signal at left-channel input (high-level signal only)
  • Speaker level inputs via RCA, JL Audio XD-CLRAIC2-SW required
  • Dual speaker terminals simplify the hookup of multiple speakers
  • Heavy duty aluminum alloy heat-sink for extreme heat dissipation
  • 3-way protection circuitry (thermal, overload, and speaker short protection)
  • Detented, Calibrated Filter Freq. Potentiometer
  • 12 dB/octave Butterworth or 24 dB/octave Linkwitz-Riley Crossover
  • Input sensitivity:
    • Low level: 800mV - 8V
    • High level: 200mV - 2V
  • Frequency Response: 10 - 1,000 Hz
  • Total Harmonic Distortion (THD): <1%
  • Signal to Noise Ratio: >100 dB ref. to rated power
  • Signal to Noise Ratio: >80 dB ref. to 1W
  • Damping Factor @4ohms: >120 / 50 Hz
  • Damping Factor @2ohms: >60/ 50 Hz
  • Selectable Low-Pass Filter Slope: 12 dB or 24 dB
  • Variable low-pass filter: 50 - 500 Hz, 12 or 24 dB/octave
  • Fuse Rating: 30A x 1 inline (not supplied)
  • 4 gauge power and ground wiring is recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
  • Weight: 3.80 lb
  • Dimensions: 6.85"W x 7.09"L x 2.05"H
  • Authorized Internet Dealer
  • 2 Year Manufacturer's Warranty
JL Audio XD300/1v2 owner’s manual

Infinity Reference 1262W

300W 12" Reference Series Dual 4 ohm Subwoofer
Quantity: 1

General Features:

  • 12" Dual 4 Ohm Reference Series Subwoofer
  • Power Handling:
    • Peak: 1200 watts
    • RMS: 300 watts
  • Impedance: Dual 4 Ohm
  • High-gloss polypropylene woofer cone ensures maximum woofer efficiency
  • Large-roll rubber surround absorbs distortions
  • Vented pole pieces provide additional cooling of the motor
  • Progressive spider provides better control at excursion limits
  • 2" Voice coil
  • Frequency response: 23-400 Hz
  • Sensitivity: 96 dB
  • Mounting Depth: 6-3/8"
  • Cutout Diameter: 11-1/16"
  • Authorized Internet Dealer
  • 1 year Manufacturer's warranty


Specifications & Details


Amplifier Power Specifications
RMS Power @ 4 ohms
200 watts x 1 channel
RMS Power @ 2 ohms
300 watts x 1 channel
Amplifier Specifications
Amplifier Class
D
Number of Channels
1 - Mono
Total RMS Power Output
300 watts
Maximum Input Gauge Size
4 AWG
Minimum Impedance Unbridged
2 ohms
Minimum Impedance Bridged
Not Bridgeable
THD at Rated RMS Power
<1.0%
Speaker Level Inputs
Yes
Preamp Outputs
1 pair
Built-in Crossover
Low-Pass (LP)
Low-Pass Crossover Frequency
50 - 500 Hz
Signal-to-Noise Ratio
>100 dB
Remote bass/level controller
Optional (Accessory required and sold separately)
Fuse Rating
30A X 1 In-Line Fuse Recommended
Subwoofer Specifications
Series
Reference Series
Subwoofer Size
12"
Voice Coil(s)
Dual
Impedance (Per Voice Coil)
4 ohms
RMS Power Handling
300 watts
Peak Power Handling
1200 watts
Woofer Surround
Rubber
Woofer Composition
Polypropylene
Minimum Sealed Box Volume
1.25 cubic feet
Maximum Sealed Box Volume
1.25 cubic feet
Minimum Ported Box Volume
2.0 cubic feet
Maximum Ported Box Volume
2.0 cubic feet
Sensitivity
93 dB
Frequency Response
23 - 400 Hz
Xmax (millimeters)
13 mm
Top-Mount Depth (Mounting Depth)
6-3/8"
Cutout Diameter
11-1/16"
Recommended Enclosure Type
Bandpass
Ported / Vented
Sealed
Warranty and Return Policy
Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Item Details


Manufacturer:

Model Number:

XD300/1v2_1262w

Weight:

20.75lbs

Internal SKU:

xd3001v2_1262w

Internal Product ID:

105803

Customer Ratings & Reviews



5 star
80%
4 star
13%
3 star
7%
2 star
0%
1 star
0%



Durability
4.7
Value
4.9
Features
4.6
Design
4.8
Usability
4.6

Customer Reviews

Sort by:

Loading...

Subwoofer by Infinity

The following review is for 1262w, which is a part of the bundle you are viewing.

Very nice sound and handling. shakes the entire car. Would buy from them again.

By Doug on April 21, 2014

66

found this helpful.

Infinity 1262w

The following review is for 1262w, which is a part of the bundle you are viewing.

Great sub for the price. I used this with a 300rms MTX amp and it was loud, deep, and clear. Would recommend for sure.

By Chris from Toronto on April 4, 2012

64

found this helpful.

Love this sub!

The following review is for 1262w, which is a part of the bundle you are viewing.

I bought one of these off of Ebay a while ago and was extremely pleased with it, so I bought a 2nd one from SonicElectronix during their Black November sale. I built my own custom ported enclosure at 2.0 cubic feet, tuned to 32hz. This sub hits the lows very well and puts out an insane amount of bass for only being a 300w RMS sub. In the enclosure that I built, it actually gives my buddy's 600w rms sub a run for it's money. I would highly recommend this sub to anyone, but also recommend that you look at the suggested enclosure size and don't skimp on a proper enclosure.

By Chris on December 21, 2013

70

found this helpful.

Sound as accurate as JL Audio w1v2's

The following review is for 1262w, which is a part of the bundle you are viewing.

I was tired of the sloppy sound from my old subs, and I always knew Infinity was known for realistic, accurate bass sound, so I grabbed me two of these and put them in a Sound Ordinance 1.25 cf braced, sealed enclosure. They sound very, very good- just like my JL's in my Explorer... I am driving them with a Rockford Fosgate T1500-1BDcp amp at 4 ohms...a bit much, but they seem to handle that power fine with the gain set halfway and the crossover at about 70 hz.. I also have some Kappa 12's in my Camaro... go for them if you can.

By Bo on November 20, 2010

59

found this helpful.

Great subwoofer at a great price.

The following review is for 1262w, which is a part of the bundle you are viewing.

My goal was to find about a 300-500 watt RMS (DVC @ 4 ohms/coil) 12" subwoofer that would be somewhere between $50-$100. After extensive research on Sonic's awesome site, I chose this model over the similar Alpine, Pioneer and Kicker models.

Pioneer TS-W310D4
Alpine SWS-12D4

The Infinity was less than $60 to my door, looks great installed in my custom ported MDF/fiber box and hits really solid. If I had it to do again, I might have built a sealed box for tighter bass and less space. It still sounds great and I have it tuned right around 33Hz.

I would highly recommend this model. If you are on the fence with a 12" sub decision, you won't be disappointed. The magnet on this thing is MASSIVE!

By Ernie on January 1, 2014

59

found this helpful.

Awesome value.

The following review is for 1262w, which is a part of the bundle you are viewing.

I recently purchased this sub for my Subaru Outback and have been more than pleased so far. It's in a sealed 1.25cu ft box, fed 500 watts @ 4 ohms. This exactly what I wanted at an amazing price. My goal was for a good sq sub that didn't require loads of power...goal met. If you're looking for a nice affordable sub look no further. Looks awesome, sounds terrific and doesn't break the bank.

Pros:
Killer price
Amazing sound quality in the recommended sealed box
Looks good

Cons:
Can't think of any off hand.

By Jordan on September 2, 2014

57

found this helpful.

Infinity Reference 1262W

The following review is for 1262w, which is a part of the bundle you are viewing.

I have two of these speakers and they do the job just fine. They are not the hardest hitting subs but they are not that poor quality neither.

By Charles on January 16, 2015

56

found this helpful.

great value

The following review is for 1262w, which is a part of the bundle you are viewing.

It's pretty good sub for that price hits hard enough for me loving this sub.

By Reggie on May 8, 2014

56

found this helpful.

Amazing

The following review is for 1262w, which is a part of the bundle you are viewing.

I bought an old set of infinitys in a box and they were a few years old, those blew within a year. I then purchased 2 Infinity 1262Ws and they've been hitting hard and proud for the past year!

By Luke on June 15, 2012

55

found this helpful.

Infinity Sub

The following review is for 1262w, which is a part of the bundle you are viewing.

this is a great product sounds very clear I love them

By Ethan on January 23, 2015

54

found this helpful.

Add-ons


Similar Products

Best selling similar products

NVX QBUS8P

• Low Profile Ported Subwoofer System
• 150 Watts RMS
• Built-In Class D Amplifier
• Variable Bass Boost
• Speaker-Level Inputs
• Wired Remote Bass Level Control

(6)

$129.99

NVX QBSTA

• 11" Spare Tire Subwoofer System
• Built-In Class D Amplifier
• Top-mount amplifier controls
• Speaker-Level Inputs
• Wired Remote Bass Level Control

$249.99

Pioneer TS-WX1210AM

• 350 watts Single 12" Subwoofer Enclosure
• 4 ohms Impedance
• Spring-loaded Terminal Posts
• Enclosure Dimensions: 10" TD x 12-1/2" BD x 19-3/4" W x 14-7/8" H

(2)

$179.99

MTX Audio TNP212D2 Terminator Dual Subwoofer Package + Amplifier

• 800W Peak (2 Subs)
• 400W RMS (2 Subs)
• 48oz. Magnet
• Terminator Series Class D Monoblock Car Amplifier
• Heavy 5/8" MDF Construction
• Black Carpeting

(153)

$279.95

Belva BPKG210v2 Dual 10" Subwoofer and Amp Package with Box and Wiring Kit

• Works with both Factory and Aftermarket Audio Systems
• Dual 10" Belva Subwoofers
• Monoblock Amp with Bass Knob
• Ported Enclosure
• Complete Amp Wiring Kit

(29)

$214.99

Related Searches


XD300/1v2_1262w small

Item added to your cart.

Price: $438.20

Essential add-ons
40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

$279.99

$89.99

Add to cart
Dynamat Sound Dampening Bulk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

$383.95

$235.99

Add to cart
Stinger Sound Dampening Bulk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for the whole car!

$219.00

$140.99

Add to cart
NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

$114.99

$99.99

Add to cart
2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

$9.99

$7.99

Add to cart
Five Piece Installer Panel Removal Tool Kit

Installer's Panel Removal Installation Tool Kit for Car Stereo, Speakers and Car Audio Installs

$18.99

$11.99

Add to cart
SMD DD-1 Distortion Detector

Set the gain of an audio amplifier quickly and accurately

$207.99

$199.99

Add to cart
Impedance Meter / Signal Generator

Easy to locate tuning frequencies of passive radiators and ported enclosures

$461.99

$451.99

Add to cart
Save up to 10 different vehicles in your garage

Loading...
Identify your vehicle and submodel details
  • Owner’s manual
  • Vehicle’s insurance card
  • Vehicle registration
  • Vehicle produced after 2005: Inside driver’s side door
  • Vehicle produced before 2005: Rear passenger doorjamb, glove box, center console, or engine compartment
Car Info Side Door Icon
Vehicle Registration Icon
Vehicle Insurance Icon